46mm 12 notch OD cup
SRAM® DUB™ Race Face® Cinch™, Rotor® BSA30, Zipp® Vuma™, Hawk Racing™ BB3086™, Kogel BSA30 and more
NOT SRAM T47 DUB

46mm 12 notch OD cup
Race Face® Cinch™, Rotor® BSA30, Zipp® Vuma™, Hawk Racing™ BB3086™, Kogel BSA30 and more

48.5mm OD 16 notch cup
FSA MegaEvo (not Mega Exo)
Wheels Mfg 30mm

48.5mm OD 16 notch cup
FSA MegaEvo (not Mega Exo)
Wheels Mfg 30mm

for 44mm OD 16 notch cups
Fits many Shimano®,Campagnolo®, Chris King®, FSA® MegaExo®, Hope™, SRAM®/Truvativ® GXP®, Race Face® X-type, Surly®, Wheels®, Fulcrum® and others external bearing threaded cups.

for 44mm OD 16 notch cups
Fits many Shimano®,Campagnolo®, Chris King®, FSA® MegaExo®, Hope™, SRAM®/Truvativ® GXP®, Race Face® X-type, Surly®, Wheels®, Fulcrum® and others external bearing threaded cups.

51mm 16 notch OD cup
 

51mm 16 notch OD cup
 

12 notch OD cup
Threadfit 30 and Threadfit 47 cups
 

12 notch OD cup
Threadfit 30 and Threadfit 47 cups
 

12 notch
Also fits Enduro BSA30 cups

12 notch
Also fits Enduro BSA30 cups

With no radius on notches for good fit on narrow flanges etc
48.5mm OD 16 notch
FSA MegaEvo (not Mega Exo)
Wheels Mfg 30mm

44mm OD 16 notch

XT 41mm OD cups. M8000 Ultegra 11-speed 6800 series

Double ended wrench for
XTR 39mm OD cups. BB93 M9000 Dura Ace BB9000
XT 41mm OD cups. M8000 Ultegra 11-speed 6800 series

This bashring is made from  6061-t6 aircraft aluminum and is made by WCM. This guard is .210 thick(5.33mm) It fits a 4 bolt crankarm with 104 BCD spacing and is meant to protect a 32 tooth chainring. This spacing size is the large majority of what is sold today for mountain bikes, such as shimano, truvative, race face, fsa, bontrager and many many more.

We gave this guard a tooth design because we found it superior to to a smooth round ring. With a tooth type this will glide over an obstacle about as well as a round guard. But once you begin to pedal and are still on the obstacle the teeth help to dig in and propel you forward rather than just slide.  We also gave it a unique overlapping machine cut finish because polished finishes are impossible to keep looking great, you can just touch them with your fingers and they scratch. Our finish is very durable in comparison and will be looking great for a long time to come. As you notice in the pics we also gave the teeth area a different finish for a very cool look. Oh, and did I mention it only weighs 77 grams !!!

This chainguard is designed for crosscountry and enduro racers and can withstand light to moderate downhill riding. If you've got 8 inches of travel and use it all on a regular basis, then this bashguard is not for you.

This bashring is made from  6061-t6 aircraft aluminum and is made by WCM. This guard is .210 thick(5.33mm) It fits a 4 bolt crankarm with 104 BCD spacing and is meant to protect a 34 tooth chainring. This spacing size is the large majority of what is sold today for mountain bikes, such as shimano, truvative, race face, fsa, bontrager and many many more.

We gave this guard a tooth design because we found it superior to to a smooth round ring. With a tooth type this will glide over an obstacle about as well as a round guard. But once you begin to pedal and are still on the obstacle the teeth help to dig in and propel you forward rather than just slide.  We also gave it a unique overlapping machine cut finish because polished finishes are impossible to keep looking great, you can just touch them with your fingers and they scratch. Our finish is very durable in comparison and will be looking great for a long time to come. As you notice in the pics we also gave the teeth area a different finish for a very cool look. Oh, and did I mention it only weighs 86 grams !!!

This chainguard is designed for crosscountry and enduro racers and can withstand light to moderate downhill riding. If you've got 8 inches of travel and use it all on a regular basis, then this bashguard is not for you.

To remove/install bore cap on Formula RX/R1 brakes

Fits the large cap on the mono M4, The X2, and both caps of the E4 and V4 also the large cap of the RX4.  This tool is compact, small enough to push into the bore to remove the cap but the big hex makes it easy to turn to restart the cap. The hex fits 16mm and 5/8" sockets

Fits the small cap on the Hope RX4,  The hex fits 16mm and 5/8" sockets

For DVO forks. The 18mm socket fits the lower legs on ALL DVO forks. It is extra long to give adequate clearance. Zero chamfer 6 sided close fit socket made from 6061 aluminium
thin walls allow for use in tight clearances
uses a 3/8 inch square drive
only for use on fork top caps etc requiring lower torques
max torque 100ft/lbs - 135Nm

For DVO damper. The 22mm socket is very thin walled to fit the compression cartridge for the DVO Diamond, the Beryl, the Onyx and both versions of Sapphire .It might be thin but it is built to last. It will only fit a DVO fork.
Zero chamfer 6 sided close fit socket made from 6061 aluminium
thin walls allow for use in tight clearances
uses a 3/8 inch square drive
only for use on fork top caps etc requiring lower torques
max torque 100ft/lbs - 135Nm

Zero chamfer 6 sided close fit socket made from 6061 aluminium
thin walls allow for use in tight clearances
uses a 3/8 inch square drive
only for use on fork top caps etc requiring lower torques
max torque 100ft/lbs - 135Nm

Zero chamfer 6 sided close fit socket made from 6061 aluminium
thin walls allow for use in tight clearances
uses a 3/8 inch square drive
only for use on fork top caps etc requiring lower torques
max torque 100ft/lbs - 135Nm

Zero chamfer 6 sided close fit socket made from 6061 aluminium
thin walls allow for use in tight clearances
uses a 3/8 inch square drive
only for use on fork top caps etc requiring lower torques
max torque 100ft/lbs - 135Nm

Zero chamfer 6 sided close fit socket made from 6061 aluminium
thin walls allow for use in tight clearances
uses a 3/8 inch square drive
only for use on fork top caps etc requiring lower torques
max torque 100ft/lbs - 135Nm

Zero chamfer 6 sided close fit socket made from 6061 aluminium
thin walls allow for use in tight clearances
uses a 3/8 inch square drive
only for use on fork top caps etc requiring lower torques
max torque 100ft/lbs - 135Nm

For Fox and Rockshox top caps

For X-Fusion, Fox, Magura top caps

For X-Fusion, Fox top caps

With 23mm 26mm and top cap

398-00-504 clone

Foot nut tools for Fox air spring and damper removal

Replaces the nylon bushing in all Mavic FTS-L and FTS-X freehubs.
MFBSTD

Replaces the nylon bushing in all Mavic FTS-L and FTS-X freehubs.
This one is .003 oversived to fit worn hubs
MFBOS

Replaces the nylon bushing in all Mavic FTS-L and FTS-X freehubs.
This one is .005 oversived to fit very worn hubs
MFBOS2

Replaces the nylon bushing in all Mavic FTS-L and FTS-X freehubs.
This one is .006 oversived to fit very worn hubs
MFBOS3

To assist seal installation over shaft
Replaces 398-00-764

For shaft sizes 8mm, 9mm, 3/8"/9.5mm, 10mm, 1/2"/12.7mm

For shaft sizes 7.4mm, 8mm, 9mm, 3/8"/9.5mm, 10mm, 1/2"/12.7mm, 15mm, 15.9mm/5/8", 16.7mm, 17.5mm/11/16"

For shaft sizes 8mm and 10mm

For body and shaft of Grip and Grip 2 dampers

CNC machined shock clamp for the 2017-2022 FOX GRIP damper and 2019-2022 GRIP2 damper for fox 32/34/36/38 and 40 models. This also fits the older CTD and FIT4 models. Which includes a bigger hole to seat the bladder assembly along with shaft and body sizes. This has the same fit as fox part # 803-01-324 with many other sizes.

To remove and install shock eyelet for shocks with a 1/2 inch bushing.
Has steps to allow for use with or without bushings installed.
3/8 square drive for torque wrench

2 pinned socket that fit Fox dhx2 and X2 rear shock cartridge caps. It fits both the red and blue 2 hole caps. It is a 3/8 square drive and has hardened pins. It is CNC machined for a precision fit.  Ref fox part number  398-00-417

Socket for red rebound base valve. Uses a 16mm - 5/8" hex on top and features hardened pins.

Socket for blue compression base valves. A 3/8 square drive and features hardened pins.

Pinned bearing housing driver that fits the 2021 Fox dhx2 and X2 rear shock Bearing Housing.
It features hardened pins and is CNC machined for a precision fit.
It has a 30mm top hex that can be used with a wrench but is also plenty tall to be used with a shifter or adjustable pliers.

IFP tool for setting the IFP depth on X2 shocks.  The top is 1.3" across and the shaft measures .990 wide. The shafts come in sizes 1.243 , 1.293 , 1.343 , 1.393 , 1.443. You just have to look at the fox chart to see what size you need for your X2 based on travel and length.

IFP tool for setting the IFP depth on X2 shocks.  The top is 1.3" across and the shaft measures .990 wide. The shafts come in sizes 1.243 , 1.293 , 1.343 , 1.393 , 1.443. You just have to look at the fox chart to see what size you need for your X2 based on travel and length.

IFP tool for setting the IFP depth on X2 shocks.  The top is 1.3" across and the shaft measures .990 wide. The shafts come in sizes 1.243 , 1.293 , 1.343 , 1.393 , 1.443. You just have to look at the fox chart to see what size you need for your X2 based on travel and length.

IFP tool for setting the IFP depth on X2 shocks.  The top is 1.3" across and the shaft measures .990 wide. The shafts come in sizes 1.243 , 1.293 , 1.343 , 1.393 , 1.443. You just have to look at the fox chart to see what size you need for your X2 based on travel and length.

IFP tool for setting the IFP depth on X2 shocks.  The top is 1.3" across and the shaft measures .990 wide. The shafts come in sizes 1.243 , 1.293 , 1.343 , 1.393 , 1.443. You just have to look at the fox chart to see what size you need for your X2 based on travel and length.

Tool for IFP removal and setting the IFP depth on X2 shocks, 2021 on.

Fits the Fox dh x2 rear shock negative seal head. It is CNC machined out of 6061 aluminum for a presision fit. It is 9.5" long. It has a 3/8 square drive so you can torque it to spec, just line the torque wrench up with the line (perpendicular to the tool). Ref fox part number  398-00-419

Machined shock clamp for the 2016-2020 FOX float dhx2 and X2. . The clamp fits the 9mm shaft and the air sleeve.

Its made of 6061 aluminum and is made for a precision fit. We left plenty of material so there is a lot of clearance when using the 9mm shaft clamp, and we made it .630 thick to fit into the tight spaces.
803-00-968/ 803-00-967 DH X2 9mm Tool

Machined shock clamp for the 2021 FOX float dhx2 and X2. . The clamp fits the 3/8 shaft and the air sleeve.

Its made of 6061 aluminum and is made for a precision fit. We left plenty of material so there is a lot of clearance when using the 3/8inch shaft clamp, and we made it .430 thick to fit the 2021 X2.
803-01-690 DH X2 3/8 inch tool

Machined shock clamp for the 2021 FOX float dhx2 and X2. . The clamp fits the 2021 x2 Rezi body and all Fox's that use the 1.25 inch body (the part you see from the outside of the shock that pushes into the rest of the shock when compressed).

We made the rezi body clamp with tons of clearance so you get 165 degrees of travel.